Ricsonix Audio and Video Return Kits

SD Card adaptor

Our SD card adaptor gives Sound Devices 552 owners the capability to change SD cards without the pain and suffering of reaching down under the mixer to change cards.
Part No. RIC.SDADPT

Power Cable

Standard Power cable to power either the Ricsonix Tx/Rx modules or any Lectrosonics with a 2.1mm DC input.
Cable has 4 pin Hirose male to R/A 2.1mm DC POS center.
Supplied in 2 suggested lengths.
Transmitter CAB.HRS4M-RADC30 - 30cm.
Receiver CAB.HRS4M-RADC50 - 50cm.

Power cable Y-Cord

We are offering this cable for those who will only have access to one Hirose panel mount connection on the rear of a camera but wish to power their SRa receiver and Ricsonix Return audio Transmitter.
The cable has a twin DC 2.1mm POS center to power the Ricsonix Transmitter and the SR receiver.
Part No. CAB.HRS4M-2RADC30 - 30cm.
Part No. CAB.HRS4M-2RADC50 - 50cm

Option 1 Cable Set

This cable set consists of the basic audio cable set as supplied with the kit when purchased.
It consists of a 5FXLR to TA3F Transmitter cable and a TA3F to RASMJ (Right angle stereo mini jack) receiver cable.
Transmitter cable - 5FXLR/ to TA3F - 30cm
Receiver Cable - RASMJ to TA3F - 50cm
Part No. CAB.OPT1SET

Option 2 Cable Set

Option 2 cable set - Timecode/audio option.
Allows the transmission of a mono mix of audio and Timecode from the camera back to the sound recordist.
This cable set comprises of the Transmitter and Receiver cables as pictured.
Transmitter cable - 5FXLR/RABNC to TA3F - 30cm
Receiver Cable - RASMJ/TA3F to TA3F - 50cm
Part No. CAB.OPT2SET

Option 3 Cable Set

Option 3 cable set - Timecode only option cables.
Allows the transmission of Timecode from the camera back to the sound recordist.
This cable set comprises of the Transmitter and Receiver cables.
Transmitter cable - RABNC to TA3F - 30cm
Receiver Cable - TA3F to TA3F - 50cm
See below for adaptor cables to allow connection to other Timecode inputs.
Part No. CAB.OPT3SET

Timecode adaptor cables

We make 3 RX Timecode adaptor cables for use with our Option 2 and Option 3 kits.
The TA3M to 5 Pin LEMO allows TC connection to a 7 series recorder.
The TA3M to 4 pole SMJ 3.5mm allows connection to a Apple iPhone to allow current Apps to display the Timecode.
The TA3M to BNC allows Timecode connection to devices that allow Timecode via this type of connector.
Part No. CAB.TCADAPT

Stereo Input cable

RASMJ to TA3F.
This cable is the same cable as supplied with the kit for the Receiver into the return socket of the mixer.
This additional cable can also be used with the Transmitter on cameras that have no 5FXLR and only have a headphone socket to return audio.
This cable is also useful for sending back audio from other devices wihich only have a SMJ fitting.
Part No. CAB.RASMJ.TA3F

Video 75ohm cable

BNC to BNC video cable.
Comes in a few different lengths and is used with our Video return kit.
Part No. cab.75-B

Camera Audo Return Adaptor

Return audio adaptor. Converts your 5FXLR cable into a SMJ to allow you to return audio from cameras that only have a headphone jack for monitoring and not a 5Pin XLR.
Part No. cab.x5m.rasmj

Spare SMA aerial as used by Video and Audio Return Kits.

Sometimes there is no available power outputs available to power your Ricsonix Transmitter.
We have met this issue by making available a 9Volt adaptor cable to power the Ricsonix Return Audio Transmitter.
Simply place a 9 Volt battery onto the adaptor and connect to the Transmitter.
You can expect over 12 hours of operation from a Pro 9Volt cell.
Can be used with the Audio Return Transmitter or Receiver.

*Prices are inclusive of GST.

Cables Supplied and Kits Assembled by We Terminate